rb20 bearing knock -help

godzilla · Post by **godzilla** » Mon Jun 08, 2009 9:56 pm

i have the same maxima and the other import motor . i checked the rail and injectors they are side feeds. so your plan is to use the backie manifold and a topfeed injector and rail.the ones i have wont work .you will have to use a custom made rail?!?!?!
as for the local rb's they were rb30e and rb20e NO de or det.well start fitting the motor this weekend to get the engine mountings right.I ma looking for a 21R toyota box ,anyone in capetown got one?

Draco · Post by **Draco** » Tue Jun 09, 2009 8:26 am

I was thinking if I use the manifold on the parthfinder typ vg that uses top feed I can just carry it over to my engine and re route all the piping.

godzilla · Post by **godzilla** » Tue Jun 09, 2009 2:07 pm

that would work, try the tow truck companys. they lve the nissan v6 hardbodys,here they bu up parts and stock pile them,and wont sell you one even if they have more than one.coming back to my questio, thething atached to the front of the cam puly can it be used from another car, or is it 6cylinger /4 cylinder specific?

Draco · Post by **Draco** » Tue Jun 09, 2009 2:40 pm

godzilla wrote:coming back to my questio, thething atached to the front of the cam puly can it be used from another car, or is it 6cylinger /4 cylinder specific?

Sorry man....what thing....cam pulley or crank pulley?

rat · Post by **rat** » Tue Jun 09, 2009 3:02 pm

Draco · Post by **Draco** » Tue Jun 09, 2009 3:30 pm

If it is the cas you are talking about it is not interchangeble between 4 and 6 cylinders....there is a "plate" inside with degrees that sends message back to computer to the alline timing and fuel....you can take the plate out and put it in the right cas....

godzilla · Post by **godzilla** » Wed Jun 10, 2009 1:33 pm

so thats what its called,cas, i need one for the rb,i found some std injectors, and a std turbo, i need plug leeds and the cas , and a 21R box and bellhousing,got new water pump, and oil pump.

godzilla · Post by **godzilla** » Wed Jun 17, 2009 11:08 am

Ok so i have a CAS now and will get the correct 6cylinder plate when i buy my Dictator management .Now who knows if a CA18 gearbox is a direct fit on the RB engines?

rat · Post by **rat** » Wed Jun 17, 2009 11:17 am

godzilla wrote:Ok so i have a CAS now and will get the correct 6cylinder plate when i buy my Dictator management .Now who knows if a CA18 gearbox is a direct fit on the RB engines?

no but think you can get a bellhousing off a old skyline to fit it

godzilla · Post by **godzilla** » Wed Jun 17, 2009 11:37 am

so that would be the skyline box from a new era wich ran rb20 and rb30 engines!? arent those scarse or willone from an L series work aswell?

rat · Post by **rat** » Wed Jun 17, 2009 11:58 am

dont know about the L series

veecee · Post by **veecee** » Thu Jun 18, 2009 2:26 am

ask sokar - i think he knows.

but apparently the bellhousing from an RB20det will fit onto your ca18 box. and then you will have the RB engine side pattern on your ca18 box!

godzilla · Post by **godzilla** » Thu Jun 18, 2009 3:30 pm

problem is i dont have any of these ..YET... but the knowlege is key before i spend even if it is a small amount. Gonna have a look at aRB20 box over the weekendfor R2500 wich is cheap,and a direct fit.

*Nissan 200SX Club - South Africa

rb20 bearing knock -help

rb

rb

Re: rb

rb

RB

Re: RB

rb

rb