Page 1 of 3
To ping or not to Ping
Posted: Wed Apr 15, 2009 2:38 pm
by Riekert
Hi!
I've got a bit of a issue regarding a rattling/pinging noise form my motor... I adjusted the timing to more or less to 15deg. Did it as described here :
http://www.frsport.com/How-To-Set-Crank ... _t_25.html
now... the car idles at about 800rpm on the timing gun at 15deg.
but it I rev it it has a loud prrrrrrrrr sound... and it comes from the knocksensor side of the motor... sounds like just under the intake mani...
So i'm not sure if this is pinging or just a rattle? the only thing is it wasn't always there... and its only when you rev... if it idles its fine. even if you take it up the rev range slowly. but if you blip it a few times you hear it.
any suggestions??
Posted: Wed Apr 15, 2009 2:41 pm
by Pinkfluffybunnys
I think its somthing loose, Have you checked all the bolts on that side?
Posted: Wed Apr 15, 2009 2:48 pm
by Riekert
Pinkfluffybunnys wrote:I think its somthing loose, Have you checked all the bolts on that side?
most of them. mmm... but you do have a valid point... well here we go.. gonna go check tonite!
Posted: Wed Apr 15, 2009 3:51 pm
by veecee
check your intake PCV check valve!
Posted: Wed Apr 15, 2009 4:09 pm
by Riekert
veecee wrote:check your intake PCV check valve!
You want me to do what? WHERE?
Posted: Wed Apr 15, 2009 9:58 pm
by veecee
your intake Positive Cranckcase Ventilation valve.
hmmm - i know the ca18 have these, pretty sure the SR have, but i cant remember where it is!
there is a marble (ballbearing) stopper in there to only allow airflow in one direction. my ca18 one used to rattle quite loudly under certain conditions!
on the intake side of the motor too!
Posted: Wed Apr 15, 2009 10:09 pm
by Riekert
oooohhhh.... hehehe
mmm will need to check that. and check for any loose nuts and bolts :/
dammit... procrastination is a bitch! hehe...
will check all that tomorrow...
Posted: Wed Apr 15, 2009 11:04 pm
by ReeceZ
what you do first is... enter command prompt then type
ping 192.sr20.motor.PCV valve -t
check if it replies
Posted: Wed Apr 15, 2009 11:09 pm
by Sparco_pro2000
lol
Posted: Thu Apr 16, 2009 7:42 am
by Charlvdw
ReeceZ wrote:what you do first is... enter command prompt then type
ping 192.sr20.motor.PCV valve -t
check if it replies
Now we * know what you do for a living.
Posted: Thu Apr 16, 2009 8:00 am
by Riekert
Charlvdw wrote:ReeceZ wrote:what you do first is... enter command prompt then type
ping 192.sr20.motor.PCV valve -t
check if it replies
Now we * know what you do for a living.
hehe nice!!!
Posted: Thu Apr 16, 2009 8:04 am
by Charlvdw
Riekert wrote:Charlvdw wrote:ReeceZ wrote:what you do first is... enter command prompt then type
ping 192.sr20.motor.PCV valve -t
check if it replies
Now we * know what you do for a living.
hehe nice!!!
This is what scares me , people in IT should be a bit sharper then average but still we sukkel with cars that nothing but problems. Not even talking about the cost to maintain. WTF?
Posted: Thu Apr 16, 2009 8:23 am
by rat
Charlvdw wrote:Riekert wrote:Charlvdw wrote:
Now we * know what you do for a living.
hehe nice!!!
This is what scares me , people in IT should be a bit sharper then average but still we sukkel with cars that nothing but problems. Not even talking about the cost to maintain. WTF?
I am sharp
Posted: Thu Apr 16, 2009 9:06 am
by ReeceZ
Charlvdw wrote:Riekert wrote:Charlvdw wrote:
Now we * know what you do for a living.
hehe nice!!!
This is what scares me , people in IT should be a bit sharper then average but still we sukkel with cars that nothing but problems. Not even talking about the cost to maintain. WTF?
Problem is kicking a car costs a lot more than smacking a monitor, I'm not even sure why guys do that cos it's not the monitors fault
Posted: Thu Apr 16, 2009 9:09 am
by rat
ReeceZ wrote:Charlvdw wrote:Riekert wrote:
hehe nice!!!
This is what scares me , people in IT should be a bit sharper then average but still we sukkel with cars that nothing but problems. Not even talking about the cost to maintain. WTF?
Problem is kicking a car costs a lot more than smacking a monitor, I'm not even sure why guys do that cos it's not the monitors fault
ja