Clutch n Brake and boost Problem

hentiebez · Post by **hentiebez** » Thu Jun 25, 2009 9:41 am

you in roodepoort, you can stop here by my work on friday about 4pm then i will show you how to do it. im in 13 nickel str technicon roodepoort

Drillergy · Post by **Drillergy** » Thu Jun 25, 2009 10:08 am

hentiebez wrote:you in roodepoort, you can stop here by my work on friday about 4pm then i will show you how to do it. im in 13 nickel str technicon roodepoort

Thanks I think Ill come through

Drillergy · Post by **Drillergy** » Fri Jun 26, 2009 12:05 pm

This morning I lost my 1st and 2nd gear, so rolled to Spares inc to put g/box oil. The thing is all the bolts at the bottom are stripped and we cannot get it off.

So I just filled 2.5 of oil without draining what was inside.

You think this is gonna cause a problem?

Thanks Hentiebez for offering me help but I had to get it sorted out urgently.
And shot to Aslam at Spares Inc.
Oh ja Riekert. He's almost there with the waterpump.

Now for the BOV testing.[/b]

hentiebez · Post by **hentiebez** » Fri Jun 26, 2009 1:16 pm

no problem in future you can ask me i will help you its no sweat

Drillergy · Post by **Drillergy** » Mon Jun 29, 2009 8:25 am

I've added gearbox oil but the clutch is still low and in the mornings, I cant get 1st and 2nd gear and only when the car heats up it then only can I select the gears.

What could be causing this?

Im gonna try to adjust the pin for the clutch hopefully it resolves the problem.

Charlvdw · Post by **Charlvdw** » Mon Jun 29, 2009 8:43 am

You cant adjust the pin i think you might need to replace the seals.

Drillergy · Post by **Drillergy** » Mon Jun 29, 2009 8:46 am

Charlvdw wrote:You cant adjust the pin i think you might need to replace the seals.

You can adjust the pin under the drivers side for a high clutch or low clutch.

What seals you refering to?

Charlvdw · Post by **Charlvdw** » Mon Jun 29, 2009 9:11 am

Drillergy wrote:
Charlvdw wrote:You cant adjust the pin i think you might need to replace the seals.
You can adjust the pin under the drivers side for a high clutch or low clutch.

What seals you refering to?

I thought you ment the one on the slave cylinder, dont think adjusting your paddle hight will solve your problem. Im talking about the slave and master cylinder seals. Bad idea for now cause youll need the car saterday.

Drillergy · Post by **Drillergy** » Mon Jun 29, 2009 9:14 am

Charlvdw wrote:
Drillergy wrote:
Charlvdw wrote:You cant adjust the pin i think you might need to replace the seals.
You can adjust the pin under the drivers side for a high clutch or low clutch.

What seals you refering to?
I thought you ment the one on the slave cylinder, dont think adjusting your paddle hight will solve your problem. Im talking about the slave and master cylinder seals. Bad idea for now cause youll need the car saterday.

Yep but its fine, Ill make a plan.

Charlvdw · Post by **Charlvdw** » Mon Jun 29, 2009 10:35 am

Does it get better if you pump it a few times?

Drillergy · Post by **Drillergy** » Mon Jun 29, 2009 10:51 am

Not really. It only starts working properly when the car heats up.

Charlvdw · Post by **Charlvdw** » Mon Jun 29, 2009 11:03 am

Youll need to get the old gearbox oil out and replace it.

Drillergy · Post by **Drillergy** » Mon Jun 29, 2009 11:22 am

Charlvdw wrote:Youll need to get the old gearbox oil out and replace it.

Damn all the bolts are stripped on the gbox.

veecee · Post by **veecee** » Mon Jun 29, 2009 11:42 am

remove the front section of propshaft and jack the front of the car up - that will get 95% of the old oil out!

once the prop is back in, fill it through the gearstick hole!

Drillergy · Post by **Drillergy** » Mon Jun 29, 2009 1:48 pm

veecee wrote:remove the front section of propshaft and jack the front of the car up - that will get 95% of the old oil out!

once the prop is back in, fill it through the gearstick hole!

I think Ill send it to my Mech to do, this is outta my league