Page 1 of 1

Rb25 neo convertion

Posted: Thu Oct 13, 2011 2:54 pm
by angelo123
Hi Guyz
I am relatively new to the forum. I am busy doing a rb neo convertion. the motor is fitted busy with wiring. I need info on the following.

1. the coils has build in igniters. So can you direct fire it from The Dictator Ecu. By just connecting the coils in pairs with the ignition output to each of them.

2. What will the charge time be for these coils.

I really need detailed info on wiring of the coils.

Thanks
:roll:

Re: Rb25 neo convertion

Posted: Thu Oct 13, 2011 3:04 pm
by Daniel
Hopefully Barry will see this and comment as I believe he has recently put a NEO in.

Re: Rb25 neo convertion

Posted: Thu Oct 13, 2011 3:48 pm
by White Fang
Yip , Daniel is Left , Ja , Barry will be your best bet ,

Re: Rb25 neo convertion

Posted: Thu Oct 13, 2011 7:52 pm
by BigKriss
Dicktator will fire your coils directly. VERY IMPORTANT not to trigger them on a FALLING edge, you will burn them out. 2 Ms dwell time is sufficient,.
Your NEO cas is wired opposite to the normal RB25 and is wired the same as the SR20 cas. Use the std. 4.7 V out from the Dicktator to power the cas . It does work with direct 12v as well but is not necessary.

I measured a stock factory NEO and the cas gets 5V.

Coils are wired in wasted spark pairs. Firing order is 153624.
Your pairs are 1 and 6-5 and 2-3 and 4.

Re: Rb25 neo convertion

Posted: Fri Oct 14, 2011 7:51 am
by angelo123
Thanks Bro.
I did wiring last nite, Got spark and injector pulse. Must just set the base timeing. O yes my cas is currently running 12v . can i leave it so or must i change it to 4.7v if i have to change. must i use the 5v you get for the tps + on the ecu....
Thanks a million

Re: Rb25 neo convertion

Posted: Fri Oct 14, 2011 7:54 am
by angelo123
are you talking about the falling edge for the home position. My one is set on the default .

Re: Rb25 neo convertion

Posted: Fri Oct 14, 2011 7:44 pm
by BigKriss
No, falling edge for the ign. trigger.

Re: Rb25 neo convertion

Posted: Fri Oct 14, 2011 10:06 pm
by White Fang
angelo123 wrote:Thanks Bro.
I did wiring last nite, Got spark and injector pulse. Must just set the base timeing. O yes my cas is currently running 12v . can i leave it so or must i change it to 4.7v if i have to change. must i use the 5v you get for the tps + on the ecu....
Thanks a million
Angelo

This is an oompie ! he dont smaak slang Bro ! :facepalm:
Lol but he under stand the slang , but he doesnt really like it ,

I just heard BK in my head go " ag nee not another one "

Re: Rb25 neo convertion

Posted: Sat Oct 15, 2011 11:37 am
by BigKriss
Yo, Tanne...I dont mind a bit of slang, as long as you don`t speak fcukin MIXIT to me. Then I`ll ignore you flat.

And the spelling !! Some guys need to go back to school ...!

Angelo, 12v is good. It will not do any damage.

Re: Rb25 neo convertion

Posted: Wed Oct 19, 2011 12:46 pm
by angelo123
Hi Big Kriss
Just concern. What trigger you talking about. You get input trigger,home and spark mode, You replied to me ign trigger. Just want to make sure settings is 100%

tHANK YOU.