Demigod...The hopefull quest for more...
Moderators: P3g4sus, Daniel, rat, Draco, Riekert
- POWDER
- Club Rep
- Posts: 1204
- Joined: Fri May 15, 2009 12:19 pm
- Car: S13
- Engine: SR
- Real Name: Mike
- Location: Johannesburg
Re: Demigod...The hopefull quest for more...
D, with that little setup, if you put a microphone in the pipe and connect to a laptop, there is software you can get to isolate frequencies.... You may be onto somthing good here... That then would give visual aid to spotting det
sent from my Sony Xperia X1
sent from my Sony Xperia X1
Carpe Diemotor - Sieze the motor today
- Nissan 200SX S13 92' SR20DET
http://200sx.za.net/phpBB3/garage_vehic ... cle&VID=14
- Nissan 200SX S13 92' SR20DET
http://200sx.za.net/phpBB3/garage_vehic ... cle&VID=14
Re: Demigod...The hopefull quest for more...
Hey buddy, yes...there are even how to's on doing the electronic setup, you just need to buy whatever and do it....
Re: Demigod...The hopefull quest for more...
Bought a new mani yesterday, most probably won't flow as good as the s/s import but will be a hell of a lot easier to remove and put back.
-
- Administrator
- Posts: 2512
- Joined: Wed Aug 17, 2011 9:10 pm
- Car: S13
- Real Name: Jason
- Location: JHB
Re: Demigod...The hopefull quest for more...
nice!
"I'd rather lose by a mile because I built my own car, than win by an inch because someone else built it for me"
Re: Demigod...The hopefull quest for more...
Thank you...maybe I'll send it for chroming...then it will be cute
Re: Demigod...The hopefull quest for more...
It looks well made and nice design.
DriftZ: "I swear if a CA18 beats my SR im getting a RB!"
Re: Demigod...The hopefull quest for more...
It does Gary....and it will be a hell of a lot easier and faster to install and take off, the bends on the import are so close that you can hardly get an m10 nut in there and the only ones that will fit in there is the oem nissan nut that's almost as small as an m8 nut, a normal m10 nut has no chance, stud has to be shortened that results in maybe being able to tighten the nut 4 threads...that's after you struggled half an hour a piece to get it to catch.
Re: Demigod...The hopefull quest for more...
Powercote it.
DriftZ: "I swear if a CA18 beats my SR im getting a RB!"
Re: Demigod...The hopefull quest for more...
Yes...that would be the right thing to do.
- Riekert
- The Overlord
- Posts: 9505
- Joined: Tue Jul 31, 2007 11:51 pm
- Car: S13
- Engine: VQ
- Location: Hermanus/Cape Town
- Contact:
Re: Demigod...The hopefull quest for more...
Didn't know you get square condoms?Draco wrote:Bought a new mani yesterday, most probably won't flow as good as the s/s import but will be a hell of a lot easier to remove and put back.
Enzio wrote:Who needs ligths? When you're going sideways forward facing lights don't do anything but confuse squirrels and sheep next to the road...
aka The Overlord
Re: Demigod...The hopefull quest for more...
I don't understand the werds koming out of you mouf...
- Riekert
- The Overlord
- Posts: 9505
- Joined: Tue Jul 31, 2007 11:51 pm
- Car: S13
- Engine: VQ
- Location: Hermanus/Cape Town
- Contact:
Re: Demigod...The hopefull quest for more...
:[
Enzio wrote:Who needs ligths? When you're going sideways forward facing lights don't do anything but confuse squirrels and sheep next to the road...
aka The Overlord
-
- Administrator
- Posts: 2512
- Joined: Wed Aug 17, 2011 9:10 pm
- Car: S13
- Real Name: Jason
- Location: JHB
Re: Demigod...The hopefull quest for more...
Did these muffs work?Draco wrote:Made myself some det cans, now I can tweak the timing and fuel a bit
"I'd rather lose by a mile because I built my own car, than win by an inch because someone else built it for me"