Nissan 200SX Club - South Africa

Posted: **Thu Jul 09, 2009 12:13 pm**

OK so how clean should an engine block be after a acid wash from an engineering company??? Pictures will be a great help.

Posted: **Thu Jul 09, 2009 12:36 pm**

flippen clean, go and check on rezlo's site at the project block's

Posted: **Thu Jul 09, 2009 12:37 pm**

should look like new

Posted: **Thu Jul 09, 2009 12:40 pm**

#$%%%%%!^!*!@#$*@P(*!*@#$!@#%&*$%*($)(%@!#$%(&*)^(*&(&*(#$%^(@#)()^(@#_^ Engineering "BOX" my sr20 looks like it was hosed down... there is like a residue everywhere.... dirt and SH!T... motherF@#$%$ is going to redo everything... I'll make him...

Posted: **Thu Jul 09, 2009 1:51 pm**

is there even a swear word that long

Posted: **Thu Jul 09, 2009 2:19 pm**

in Afrikaans yes (but its a combination of a couple without a space or breath)

Posted: **Thu Jul 09, 2009 2:44 pm**

Stupid F@#$ says that the I got is the job I paid for... AAAAAAAAARGH

I nearly hit him with the F@#$ing head... ok so back to the drawing board... so here is where we are now...

Payed SPARTAN MOTOR ENGINEERING IN SPARTAN R2500 for doing F-ALL.

Handed stuff in with JCB Engine Rebuilders in Sebenza Edenvale... now these guys run 3 V8 challenge racecars so hopefully they can fix my stuff properly and I will have a decent motor. Their workmanship looks awesome and we will see where we are at as time goes on...

Sorry about some of the bad language used but I am seriously p-ed off.

Posted: **Thu Jul 09, 2009 2:46 pm**

no worries when you waste your hard earnd money like that then by all means swear kick slap drive over whatever you please but if you waste you pimp cash from all your girls then i suggest you send them on double shifts

Posted: **Thu Jul 09, 2009 2:47 pm**

no sx owner/driver is a virgin to these much required vocal expresions...

good luck pheonix...

we should start a bad service section in the forum - ie don't use the following f*ers

Posted: **Thu Jul 09, 2009 2:50 pm**

Yep

Once we locked a well known tuner and his staff inside his workshop after R60 000 and still a non running vehicle...

Hehehehehe

Posted: **Thu Jul 09, 2009 7:00 pm**

Why doesn't this forum have a list of all the kak workshops/mechanics/vendors?

That way others would be saved a raping.

It should stickied at the top of the technical section, "Buyers Beware" or something similar.

Posted: **Thu Jul 09, 2009 11:42 pm**

jon wrote:Why doesn't this forum have a list of all the kak workshops/mechanics/vendors?

That way others would be saved a raping.

It should stickied at the top of the technical section, "Buyers Beware" or something similar.

looks like riekert has made one

Posted: **Fri Jul 10, 2009 7:59 am**

rat wrote:
jon wrote:Why doesn't this forum have a list of all the kak workshops/mechanics/vendors?

That way others would be saved a raping.

It should stickied at the top of the technical section, "Buyers Beware" or something similar.
looks like riekert has made one

I think promote the good guys and discredit the bad ones...

Posted: **Fri Jul 10, 2009 8:17 am**

Drillergy wrote:
rat wrote:
jon wrote:Why doesn't this forum have a list of all the kak workshops/mechanics/vendors?

That way others would be saved a raping.

It should stickied at the top of the technical section, "Buyers Beware" or something similar.
looks like riekert has made one
I think promote the good guys and discredit the bad ones...

obviuuuuusss!

Posted: **Fri Jul 10, 2009 10:14 am**

phoenix s14 wrote:Stupid F@#$ says that the I got is the job I paid for... AAAAAAAAARGH I nearly hit him with the F@#$ing head... ok so back to the drawing board... so here is where we are now...

Payed SPARTAN MOTOR ENGINEERING IN SPARTAN R2500 for doing F-ALL.

You paid someone R2500 to wash an engine block??? Thats your problem right there.

Nissan 200SX Club - South Africa

How clean???

How clean???