Posted: Mon Feb 21, 2011 10:28 pm
Would be good if you had the cash to rebuild it from the ground up for a piece of mind
Would be good if you had the cash to rebuild it from the ground up for a piece of mind
Nissan 200SX Club - South Africa
Forum for owners of the Nissan 200SX in South Africa
https://forum.sxoc.co.za/
Project - Evil D (L28... err... RB25 scratch that CA18.... nope wrong again swapped SilEighty)
Page 60 of 87
Would be good if you had the cash to rebuild it from the ground up for a piece of mind
Posted: Mon Feb 21, 2011 10:30 pm
same man... ag maybe someday 
haha
might sell the gearbox ect to rebuild the old SR...
hahamight sell the gearbox ect to rebuild the old SR...
Posted: Tue Feb 22, 2011 6:49 am
those bloody agents againRiekert wrote:haha sweet man!!
Well the head was a bit gunky... but ja... motor was in good condition but the previous rebuild screw something up I think...
Posted: Tue Feb 22, 2011 7:08 am
At least it was running strong before all this happened 
Posted: Wed Feb 23, 2011 9:22 pm
haha only saw now that the thread hit page 60 
Posted: Wed Feb 23, 2011 11:48 pm
Less posting BS and more fixing the SX.
Posted: Thu Feb 24, 2011 6:52 am
+1
Posted: Thu Feb 24, 2011 8:22 am
yeah yeah....
I'm removing the head again... sending it in to get checked for shim clearance ect ect.
GEtting a new HG and checking that the pistons is 100%
should be respraying the front end end of the month... so should look good.
I'm removing the head again... sending it in to get checked for shim clearance ect ect.
GEtting a new HG and checking that the pistons is 100%
should be respraying the front end end of the month... so should look good.
Posted: Sun Feb 27, 2011 11:11 pm
so at least I got to do something on the SX this weeked... my new wheels fitted.
15x7j Doesn't look too bad.
Now for the removal of the rest of the head and getting the new headgasket etc
15x7j Doesn't look too bad.
Now for the removal of the rest of the head and getting the new headgasket etc
Posted: Thu Mar 10, 2011 9:03 am
Ok, so I removed the head last nite... valves looks 100% still... tonite I'm going to measure the valve clearance ect ect...
I also turned the motor with the head off and it turns fine... sigh...
Will do the head completely... then drop the sump just to see it there is any crap in there. if not fit everything again and swing it again to see whats up.
I also turned the motor with the head off and it turns fine... sigh...
Will do the head completely... then drop the sump just to see it there is any crap in there. if not fit everything again and swing it again to see whats up.
Posted: Thu Mar 10, 2011 9:05 am
Good luck man! hope its not something major!
Posted: Thu Mar 10, 2011 1:58 pm
Thanx me too! if it is then... well I don't know
pull the motor and redo, hahahahaha.
Lemme know when your online again.
pull the motor and redo, hahahahaha.
Lemme know when your online again.
Posted: Thu Mar 10, 2011 2:04 pm
Whats the plan here now?
Posted: Thu Mar 10, 2011 2:13 pm
Well basically want to get the motor sorted, then see from there... Think the best is to sell the SR and get myself another one...
Posted: Tue Mar 22, 2011 7:52 pm
where do you get those IC piping from? were they custom made?