Page 23 of 35
Re: Project See Why.
Posted: Tue May 28, 2013 7:15 pm
by antman
Hey Charl...good job with the rear end. I need to do the same on the 300. I need to replace all the bushes as well, were any of them a bugger to remove, I know one of them has sleeve which does not come with the energy kit...I think? Did you have to burn out any of them?
Whats the going rate to powder coat all those parts.
Looks good I must say.
Tony
Re: Project See Why.
Posted: Wed May 29, 2013 9:53 am
by Charlvdw
antman wrote:Hey Charl...good job with the rear end. I need to do the same on the 300. I need to replace all the bushes as well, were any of them a bugger to remove, I know one of them has sleeve which does not come with the energy kit...I think? Did you have to burn out any of them?
Whats the going rate to powder coat all those parts.
Looks good I must say.
Tony
Hey Tony
All of them were kak to get out
I pressed them out but you still need to cut out a sleeve here and there.
Powder coating were R450.
Re: Project See Why.
Posted: Wed May 29, 2013 6:16 pm
by antman
I am dreading doing that job, I dont have a press so I will burn the rubber bush out, will definately have to powder coat after the heat treatment to prevent rust.
So whats next on your build, why you opened up the diff....was it faulty or you just wanted to whats inside...ha ha ha.
Re: Project See Why.
Posted: Wed May 29, 2013 6:40 pm
by Charlvdw
antman wrote:I am dreading doing that job, I dont have a press so I will burn the rubber bush out, will definately have to powder coat after the heat treatment to prevent rust.
So whats next on your build, why you opened up the diff....was it faulty or you just wanted to whats inside...ha ha ha.
Just wanted to check it out. No curiosity at all.
Re: Project See Why.
Posted: Mon Jun 03, 2013 8:27 am
by Charlvdw
And while the diff is apart....
Re: Project See Why.
Posted: Mon Jun 03, 2013 5:43 pm
by SonOfAnarchy ZA
nice dude looks good
Re: Project See Why.
Posted: Mon Jun 03, 2013 7:28 pm
by Charlvdw
SonOfAnarchy ZA wrote:nice dude looks good
Thanx Jason.
Re: Project See Why.
Posted: Mon Jun 03, 2013 11:40 pm
by POWDER
Ey lookin good man, wish I had the energy to do that. . . Would love to stripp the suspention for a good polish up too
Sent from some crappy hand held device.
Re: Project See Why.
Posted: Tue Jun 04, 2013 6:56 am
by Charlvdw
Had to do it sometime.
Re: Project See Why.
Posted: Tue Jun 04, 2013 8:22 am
by Ero_sennin
lyk goed!
Jis daai taffeltjie is al so baie kleure gewees
Re: Project See Why.
Posted: Tue Jun 04, 2013 11:05 am
by Charlvdw
Lekker tafel daai.
Re: Project See Why.
Posted: Wed Jun 12, 2013 11:41 am
by Charlvdw
And then:
Re: Project See Why.
Posted: Thu Jun 13, 2013 7:26 am
by antman
Hey Charl...looking neat and clean daar onder...we going to have to flip your car on its roof to really appreciate all the work you have done underneath
It gives one a good feeling to know all is bright and clean chassis wise even though its not always visable....going to do similar work.
Cheers
Re: Project See Why.
Posted: Thu Jun 13, 2013 4:28 pm
by Charlvdw
Jip, just have to do the same topside aswell sometime.
Re: Project See Why.
Posted: Thu Jun 13, 2013 6:49 pm
by antman
You better stop making it look beautiful or you won't want to sell it.