dont have a clue dude the previous owner did itEro_sennin wrote:Doesn't powder coating go through a very hot oven, at least my stuff I have sent does and takes kak long to cool down?
Project ANARCHY
Moderators: P3g4sus, Daniel, rat, Draco, Riekert
-
SonOfAnarchy ZA
- Administrator
- Posts: 2512
- Joined: Wed Aug 17, 2011 9:10 pm
- Car: S13
- Real Name: Jason
- Location: JHB
Re: Project ANARCHY
"I'd rather lose by a mile because I built my own car, than win by an inch because someone else built it for me"
Re: Project ANARCHY
It's not powdercoated. It would have melted into a ball in the oven.
It would have been rattle canned - you can get a very good finish if you prep and spray it correctly.
It would have been rattle canned - you can get a very good finish if you prep and spray it correctly.
S13 CA18DET, NIStune and...oh wait no that's gone..... -
SonOfAnarchy ZA
- Administrator
- Posts: 2512
- Joined: Wed Aug 17, 2011 9:10 pm
- Car: S13
- Real Name: Jason
- Location: JHB
Re: Project ANARCHY
possible the guy i bought it from powder coated a few things cuz he owns a powder coating shop. but ja come to think about it its impossible to powder coat something that doesnt conduct and wont melt lol
"I'd rather lose by a mile because I built my own car, than win by an inch because someone else built it for me"
-
SonOfAnarchy ZA
- Administrator
- Posts: 2512
- Joined: Wed Aug 17, 2011 9:10 pm
- Car: S13
- Real Name: Jason
- Location: JHB
Re: Project ANARCHY
Lamin-X 
"I'd rather lose by a mile because I built my own car, than win by an inch because someone else built it for me"
-
MacNello
- Slipping Clutch
- Posts: 92
- Joined: Mon Jul 11, 2011 1:37 pm
- Car: S13
- Real Name: Nello
- Location: Jozi
Re: Project ANARCHY
looks fresh ! See you been attacking that orange peel hard style - liking this colour
-
SonOfAnarchy ZA
- Administrator
- Posts: 2512
- Joined: Wed Aug 17, 2011 9:10 pm
- Car: S13
- Real Name: Jason
- Location: JHB
Re: Project ANARCHY
after 3 polishes 
my hands are broken
my hands are broken
"I'd rather lose by a mile because I built my own car, than win by an inch because someone else built it for me"
-
POWDER
- Club Rep
- Posts: 1204
- Joined: Fri May 15, 2009 12:19 pm
- Car: S13
- Engine: SR
- Real Name: Mike
- Location: Johannesburg
Re: Project ANARCHY
OK Mr. Curry Powder ready to powdercoat tings for u 
Sent from some crappy hand held device.
Sent from some crappy hand held device.
Carpe Diemotor - Sieze the motor today
- Nissan 200SX S13 92' SR20DET
http://200sx.za.net/phpBB3/garage_vehic ... cle&VID=14
- Nissan 200SX S13 92' SR20DET
http://200sx.za.net/phpBB3/garage_vehic ... cle&VID=14
-
Adrian
- 0.9 Bar Boost
- Posts: 936
- Joined: Wed Oct 06, 2010 12:23 pm
- Car: S13
- Real Name: ????
- Location: jhb
Re: Project ANARCHY
dude is she alive yet or what!!!!!!!!!!!!!
-
SonOfAnarchy ZA
- Administrator
- Posts: 2512
- Joined: Wed Aug 17, 2011 9:10 pm
- Car: S13
- Real Name: Jason
- Location: JHB
Re: Project ANARCHY
jap bled the brakes and clutch taking her on saturday to get exhaust done! but still cant get the rev counter to work
but still cant get the rev counter to work"I'd rather lose by a mile because I built my own car, than win by an inch because someone else built it for me"
-
Adrian
- 0.9 Bar Boost
- Posts: 936
- Joined: Wed Oct 06, 2010 12:23 pm
- Car: S13
- Real Name: ????
- Location: jhb
Re: Project ANARCHY
Its 1 wire to ur dash
Have u found the blue wire to your counTer
Have u found the blue wire to your counTer
-
SonOfAnarchy ZA
- Administrator
- Posts: 2512
- Joined: Wed Aug 17, 2011 9:10 pm
- Car: S13
- Real Name: Jason
- Location: JHB
Re: Project ANARCHY
from what i can see its a yellow and red wire for the tacho and blue and black for temp sensor
"I'd rather lose by a mile because I built my own car, than win by an inch because someone else built it for me"
-
Adrian
- 0.9 Bar Boost
- Posts: 936
- Joined: Wed Oct 06, 2010 12:23 pm
- Car: S13
- Real Name: ????
- Location: jhb
Re: Project ANARCHY
Ok well just check. I left a piece of the original wire from the sx harness on. Just hunt for thoes and check in your workshop book for them..
Ya blue is water temp for the gauge.. Its been some time so can't remember the exact 1
Ya blue is water temp for the gauge.. Its been some time so can't remember the exact 1
-
SonOfAnarchy ZA
- Administrator
- Posts: 2512
- Joined: Wed Aug 17, 2011 9:10 pm
- Car: S13
- Real Name: Jason
- Location: JHB
Re: Project ANARCHY
So sx went on a trip to get he down pipe made up. Finally got to drive the car properly for the first time in a year and a half. car pulls very strong still on low boost but feels great. Had a couple of teething issues but thanks goodness that motor was built right(thanks Adrian) otherwise the might have been sad news today. After fiddling around with my grounding putting new plugs and sorting a water line out the car is pulling strong again
"I'd rather lose by a mile because I built my own car, than win by an inch because someone else built it for me"
-
jdm200sx
- 0.1 Bar Boost
- Posts: 197
- Joined: Mon May 28, 2012 6:04 pm
- Car: S13
- Real Name: Ridwaan
- Location: CapeTown
Re: Project ANARCHY
Well worth the effort man! Car is looking awesome
Life is not a journey to the grave with the intention of arriving safely in one pretty and well-preserved piece...but to skid in broadside, thoroughly used up, worn out, and defiantly shouting "wow, what a ride."
-
Adrian
- 0.9 Bar Boost
- Posts: 936
- Joined: Wed Oct 06, 2010 12:23 pm
- Car: S13
- Real Name: ????
- Location: jhb
Re: Project ANARCHY
You still running at .8? Enjoy her man.. I want a spin dude!!
