Re: Project: 200SX S13, drift purpose AKA Jiyuu
Posted: Sun Jan 01, 2012 8:16 pm
Wow! No. I need an engine lift.
Nissan 200SX Club - South Africa
Forum for owners of the Nissan 200SX in South Africa
https://forum.sxoc.co.za/
Project: 200SX S13, drift purpose AKA Jiyuu
Page 2 of 6
Re: Project: 200SX S13, drift purpose AKA Jiyuu
Posted: Sun Jan 01, 2012 8:32 pm
Haha I see the ca has no respect at all
Project: 200SX S13, drift purpose AKA Jiyuu
Posted: Sun Jan 01, 2012 9:30 pm
The CA18... Motor.
Easy to remove with grinder and cutting torch. The smaller you cut it the easier it comes out. DIY
Easy to remove with grinder and cutting torch. The smaller you cut it the easier it comes out. DIY
Project: 200SX S13, drift purpose AKA Jiyuu
Posted: Sun Jan 01, 2012 9:31 pm
You going I use the CA to drift?
Re: Project: 200SX S13, drift purpose AKA Jiyuu
Posted: Sun Jan 01, 2012 9:55 pm
Lol I'm not liking that idea at all!
Ya using the CA for now, going SR later
Ya using the CA for now, going SR later
Re: Project: 200SX S13, drift purpose AKA Jiyuu
Posted: Mon Jan 02, 2012 2:51 pm
ok, well then ignor my previous removal instructions.
Use engine lift then
Remove as much as possible to keep the car light, as the CA18 is slightly under powered for drifting.
Use engine lift then
Remove as much as possible to keep the car light, as the CA18 is slightly under powered for drifting.
Re: Project: 200SX S13, drift purpose AKA Jiyuu
Posted: Mon Jan 02, 2012 8:46 pm
LOL!! 
Thanx Adrian for your help today! passenger side sound deadening gone, taken out ABS, remaining aircon piping, aerial, stock sound, brake lines, ignition lighter, alarm, central locking, all remaining foreign wiring and random shit and discovered that I have quite a few large holes due to rust where the rear wing used to be.... Fibre glass boot here we come!!
After a clean:
Removal of the sound deadening, only the front side so far:
And some rust....
Taking motor out tomorrow and I'll see whats what then...
Thanx Adrian for your help today! passenger side sound deadening gone, taken out ABS, remaining aircon piping, aerial, stock sound, brake lines, ignition lighter, alarm, central locking, all remaining foreign wiring and random shit and discovered that I have quite a few large holes due to rust where the rear wing used to be.... Fibre glass boot here we come!!
After a clean:
Removal of the sound deadening, only the front side so far:
And some rust....
Taking motor out tomorrow and I'll see whats what then...
Re: Project: 200SX S13, drift purpose AKA Jiyuu
Posted: Mon Jan 02, 2012 9:02 pm
Any time zookie!!!!! Was fun till we got to the boot lid....
Ag atleast you know what's up over there now...
Ag atleast you know what's up over there now...
Re: Project: 200SX S13, drift purpose AKA Jiyuu
Posted: Mon Jan 02, 2012 10:09 pm
Lol! I think u were more pissed off than I was!
Re: Project: 200SX S13, drift purpose AKA Jiyuu
Posted: Tue Jan 03, 2012 8:11 am
The more rusted away, the lighter the car!
Re: Project: 200SX S13, drift purpose AKA Jiyuu
Posted: Tue Jan 03, 2012 9:06 am
Hahahaha daily weight sheddingSilviaS13 wrote:The more rusted away, the lighter the car!
Re: Project: 200SX S13, drift purpose AKA Jiyuu
Posted: Tue Jan 03, 2012 9:16 am
Hahahaha! Like I said, fibreglass here we come! And I'm gonna replace the rear window with plexi-glass
Re: Project: 200SX S13, drift purpose AKA Jiyuu
Posted: Tue Jan 03, 2012 12:53 pm
Don't worry, you are not the only one working on a new project...
I am also busy with another baby
I am also busy with another baby
Re: Project: 200SX S13, drift purpose AKA Jiyuu
Posted: Tue Jan 03, 2012 5:37 pm
Awesome!!! Knowing u I'm sure she's gonna be epic!!
Re: Project: 200SX S13, drift purpose AKA Jiyuu
Posted: Wed Jan 04, 2012 7:33 am
Did you come right with Engine Lift ?
i have you you can use !
i have you you can use !