Page 2 of 2
Posted: Fri Nov 23, 2007 5:10 pm
by ChemCool
I like this, and I want that
Chem
Posted: Sat Nov 24, 2007 9:02 am
by johansx
MadMan EMS Pricing in ZAR excl Vat October 2008
Recommed Retail Price Johannesburg RSA
MADMAN Products Including Vat
EMS1 Rectangular 1846.80
EMS2 Square 1430.70
EGT Probe 100mm + 2m lead 262.20
EGT Probe 30mm + 2m lead 262.20
Land Rover Td5 EGT plate Tapped for EGT probe 57.00
Land Rover Tdi EGT Plate Tapped for EGT probe 27.00
Land Rover Td5 Coolant Adapter Tapped for Temp sender 136.80
Land Rover Td5 Sump plug adapter Tapped Sump plug for oil temp 57.00
Land Rover LT230 Tapped Sump plug for oil temp 57.00
Due Soon - MadMan CLD Coolant Level Detector TBA
Buy-In Stock
VDO Pressure Sender 360/081/029/012 433.20
VDO Temperature sender 323/801/009/001 91.20
Oil Pressure Tee piece 1/8 NPT Running Tee 557.00
Coolant Level Sensor Drill 2 x 1mm hole 273.60
Float Switch RS # 3389744 Drill 22mm hole 273.60
Posted: Sat Nov 24, 2007 10:58 am
by Toby
The level meter in the water bottle is not foolproof though. In my case, where a radiator hose blew (sounded like a stone hit the underside of the car), there was still water in the water bottle as I continued to drive. I'd be happier if the sensor could detect:
FFFLLLLOOOOOWWWWWW
of water
Posted: Mon Nov 26, 2007 8:18 am
by Gary57
The Madman thing does look good but I have most of those gauges in the car except oil pressure and temp.
Johansx where did you mount the board and the sensor?? I like that idea a lot, even more than the Alfa one. Would it be possible for this to just simply turn on the LED in the cluster that is not being used?? I dont need the 3 stage one just a simple system when there is no water the light must come on.
Posted: Mon Nov 26, 2007 10:22 am
by johansx
Gary57 wrote:The Madman thing does look good but I have most of those gauges in the car except oil pressure and temp.
Johansx where did you mount the board and the sensor?? I like that idea a lot, even more than the Alfa one. Would it be possible for this to just simply turn on the LED in the cluster that is not being used?? I dont need the 3 stage one just a simple system when there is no water the light must come on.
Build this about 3 years ago....
still not mounted. Best place is probably to mount it at the highest point. Me thinks just where the top rubber pipe goes into the radiator. Yes, you can mount a simple LED only if there is no water at all. It comes with 3 LEDS, red, orange and green. Just extend the red 1 to anywhere on the dash. I want a red flashing strobe light and and a cow protter under my seat ...
Biggest problem is to build the level sensor fitting into the main radiator top hose. Spark plug electrodes with the ceramic insolator should work, just don't know if the steam will provide enough dampness to give a false reading.
Posted: Mon Nov 26, 2007 10:26 am
by Gary57
Why cant you use the Golfs water sensor?? It work in exactly the same way. Where can I find that board thing in the electronics123 website?? I must look into the Golf thing a bit more.
Posted: Mon Nov 26, 2007 10:36 am
by johansx
Is the Golf sensor not some float with a switch?
Look for "Liquid Level Controller"
http://www.electronics123.co.za/Main.as ... goryID=923
http://www.electronics123.co.za/Main.as ... geNumber=1
The sensor board on the left needs replacing to fit into the water system.
Posted: Mon Nov 26, 2007 10:40 am
by Gary57
The Golfs washer bottle use the electrode type.
Posted: Mon Nov 26, 2007 4:48 pm
by johansx
Where is this electrode located, radiator or bottle? Picture anybody?
Posted: Tue Nov 27, 2007 8:22 am
by Gary57
Bottle. It would be easy to mount that sensor in the upper radiator hose, make the hose out of stainless.