Page 68 of 87
Re: Project - Evil D
Posted: Sun Dec 30, 2012 5:06 pm
by Riekert
Hahaha I had a couple of beers
fetching my engine crane tomorrow. So will be dropping in the motor in the week. Searching for my turbo feed lines as I think I misplaced them:sad:
Sent from my GT-I9100 using Tapatalk 2
Re: Project - Evil D
Posted: Sun Dec 30, 2012 8:29 pm
by Riekert
Ok so found my feedlines
putting turbo on tomorrow. Yay
Sent from my GT-I9100 using Tapatalk 2
Re: Project - Evil D
Posted: Sun Dec 30, 2012 9:06 pm
by BigKriss
I`m keeping an eye on this boet ! Just so you know you have to put it in tomorrow !
Cannot wait to actually know it moves under it`s own steam again..
Re: Project - Evil D
Posted: Sun Dec 30, 2012 9:39 pm
by Riekert
Hahaha thanx. And I'll post pics. Hehe
Sent from my GT-I9100 using Tapatalk 2
Re: Project - Evil D
Posted: Sun Dec 30, 2012 9:39 pm
by Riekert
Oh and same! Can't wait till its in!!
Sent from my GT-I9100 using Tapatalk 2
Re: Project - Evil D
Posted: Thu Jan 03, 2013 11:12 am
by BigKriss
Tick tock bud, is that engine in yet ???
Re: Project - Evil D
Posted: Thu Jan 03, 2013 11:18 am
by SonOfAnarchy ZA
its not December yet BK
Re: Project - Evil D
Posted: Fri Jan 04, 2013 10:31 am
by Riekert
hahaha. Ya ya... I forgot the pics
Will upload over the weekend
Sent from my GT-I9100 using Tapatalk 2
Re: Project - Evil D
Posted: Sat Jan 05, 2013 2:46 pm
by Riekert
So... Did some stuff. But couldn't fit the turbo as I don't have a sirclip remover
as I need to clock the turbo to fit it... Sigh... Any how. Some pics
Basically engine mounts on, alternator on, power steering pump on and turbo feed lines on... Just need to do injectors turbo and sump. Then I can drop the motor in.
Where can I get a sirclip tongs?
Laters!
Sent from my GT-I9100 using Tapatalk 2
Re: Project - Evil D
Posted: Sun Jan 06, 2013 10:09 pm
by Riekert
So still looking for a sirclip tool... At least got the clutch and flywheel on. Now just sump and injector rail. Almost there!!!
Sent from my GT-I9100 using Tapatalk 2
Re: Project - Evil D
Posted: Mon Jan 07, 2013 7:54 am
by Draco
Good stuff Crieket!! it's time!!
Re: Project - Evil D
Posted: Wed Jan 09, 2013 9:39 pm
by Riekert
So still waiting for the circlip pliers...
hopefully be able to drop the motor in over the weekend
Man I can't wait!!
Really hope it starts
:-?:mrgreen:
Hahaha
Sent from my GT-I9100 using Tapatalk 2
Re: Project - Evil D
Posted: Thu Jan 10, 2013 8:07 am
by Draco
Hope so too man, shit happens to us 200sx lot....
Re: Project - Evil D
Posted: Thu Jan 10, 2013 8:19 am
by Riekert
Very true... Can't wait anymore!!!
Sent from my GT-I9100 using Tapatalk 2
Re: Project - Evil D
Posted: Thu Jan 10, 2013 8:50 am
by SonOfAnarchy ZA
