Project: D200SX-R SR13 AKA The Rice Rocket
Moderators: P3g4sus, Daniel, rat, Draco, Riekert
- Drillergy
- SX Forumholic
- Posts: 2078
- Joined: Fri Sep 21, 2007 10:18 am
- Car: S13
- Engine: SR
- Real Name: Darryl
- Location: Midrand
- Contact:
Project: D200SX-R SR13 AKA The Rice Rocket
So after many years I decided that the CA18DET was on its last legs and a I could have opted to refresh it but decided to do a motor swop.
I will be doing the build in stages.
Stage 1- Engine Build
S13 SR20DET Motor swop
FMIC 300x600x76 Tube and Fin design
GodSpeed 76mm Stainless Steel Exhaust x2 Silencers Madrel dairy Bent
ACTPerformance T3/04 custom Down Pipe 76mm
Garrett T3/T4E 50A/R
Microtech LT10s with 1GB x4 Ignition booster and Hand controller
80mm swiss movement Stepper Boost Gauge 80mm
52mm swiss movement Stepper Oil pressure gauge
52mm swiss movement Stepper Water Temp Gauge
52mm Innovate oil pressure guage and sender to be fitted
550cc Denso Injectors
Circuit Sport Top Feed Injector Fuel Rail
Walbro Fuel Pump 255lt
Circuit Sport Magnetic oil drain plug
Excell Wastegate 38mm 0.8 Bar Spring
Vented screamer pipe
Gizzmo MS-IBC Electronic Boost Controller
Tial Blow off valve
53mm Aluminium Radiator
12 inch puller fan
12 inch Opel OPC fan twin speed
Works Oil FIller Cap
Tomei Rocker Arm Stoppers
Wiseco Pistons
ACL Race series Bearings
Modified Oil Catch Can
Drift hi capacity sump with baffle doors
DIF Oil Feed and Drain lines
Drivetrain
Spec Stage 3 clutch
Locked Diff
Diff Brace
Suspension
Traxxion Coilovers
Alutech Front and Rear Struts
Circuit Sports hardended Tie Rods and Ends with anti bump steer
Aluminium Subframe spacers and C collars
Braking
Z32 4 pot calipers
DIF Braided Brake Lines
ABS delete
Optimum Balance Performance (OBP) Hydraulic Handbrake
Exterior
Smoked Rear Aftermarket Lights
Smoked front bumper Lights
Wheels and Tyres
Advan RG2 17 inch in Pearl White
New Bridgestones up front
Rears - Various Tyres
I will be doing the build in stages.
Stage 1- Engine Build
S13 SR20DET Motor swop
FMIC 300x600x76 Tube and Fin design
GodSpeed 76mm Stainless Steel Exhaust x2 Silencers Madrel dairy Bent
ACTPerformance T3/04 custom Down Pipe 76mm
Garrett T3/T4E 50A/R
Microtech LT10s with 1GB x4 Ignition booster and Hand controller
80mm swiss movement Stepper Boost Gauge 80mm
52mm swiss movement Stepper Oil pressure gauge
52mm swiss movement Stepper Water Temp Gauge
52mm Innovate oil pressure guage and sender to be fitted
550cc Denso Injectors
Circuit Sport Top Feed Injector Fuel Rail
Walbro Fuel Pump 255lt
Circuit Sport Magnetic oil drain plug
Excell Wastegate 38mm 0.8 Bar Spring
Vented screamer pipe
Gizzmo MS-IBC Electronic Boost Controller
Tial Blow off valve
53mm Aluminium Radiator
12 inch puller fan
12 inch Opel OPC fan twin speed
Works Oil FIller Cap
Tomei Rocker Arm Stoppers
Wiseco Pistons
ACL Race series Bearings
Modified Oil Catch Can
Drift hi capacity sump with baffle doors
DIF Oil Feed and Drain lines
Drivetrain
Spec Stage 3 clutch
Locked Diff
Diff Brace
Suspension
Traxxion Coilovers
Alutech Front and Rear Struts
Circuit Sports hardended Tie Rods and Ends with anti bump steer
Aluminium Subframe spacers and C collars
Braking
Z32 4 pot calipers
DIF Braided Brake Lines
ABS delete
Optimum Balance Performance (OBP) Hydraulic Handbrake
Exterior
Smoked Rear Aftermarket Lights
Smoked front bumper Lights
Wheels and Tyres
Advan RG2 17 inch in Pearl White
New Bridgestones up front
Rears - Various Tyres
Last edited by Drillergy on Mon Mar 23, 2015 10:09 am, edited 13 times in total.
- POWDER
- Club Rep
- Posts: 1204
- Joined: Fri May 15, 2009 12:19 pm
- Car: S13
- Engine: SR
- Real Name: Mike
- Location: Johannesburg
lookin forward to this one, gonna be nice..... Welcome to team SR my boy...
Same here, let me know if u wanna know how an SR pulls...
Same here, let me know if u wanna know how an SR pulls...
Carpe Diemotor - Sieze the motor today
- Nissan 200SX S13 92' SR20DET
http://200sx.za.net/phpBB3/garage_vehic ... cle&VID=14
- Nissan 200SX S13 92' SR20DET
http://200sx.za.net/phpBB3/garage_vehic ... cle&VID=14
- POWDER
- Club Rep
- Posts: 1204
- Joined: Fri May 15, 2009 12:19 pm
- Car: S13
- Engine: SR
- Real Name: Mike
- Location: Johannesburg
Hows about I pick u up sometime den we go check Henti out 2getha... I gots to go show my boet my car n e way....Drillergy wrote:Thanks guys.
Will be posting pics from monday
@Hentie and Michael, I might just take you up on that offer. Need some inspiration for the build.
P.S. Need a comparison run to check how well my SR is running n e way ;D
Carpe Diemotor - Sieze the motor today
- Nissan 200SX S13 92' SR20DET
http://200sx.za.net/phpBB3/garage_vehic ... cle&VID=14
- Nissan 200SX S13 92' SR20DET
http://200sx.za.net/phpBB3/garage_vehic ... cle&VID=14
- Drillergy
- SX Forumholic
- Posts: 2078
- Joined: Fri Sep 21, 2007 10:18 am
- Car: S13
- Engine: SR
- Real Name: Darryl
- Location: Midrand
- Contact:
Re: Project: Drillergy's Sidewinder
So busy collecting items.
I got a Turbo, I dunno what turbo it is but Im guessing its a T3/T4.
Cusco Front Tower Strut
Solid Aluminium Steering Bush- Blue Anodised
And a Sneak Peak of the SR20
I got a Turbo, I dunno what turbo it is but Im guessing its a T3/T4.
Cusco Front Tower Strut
Solid Aluminium Steering Bush- Blue Anodised
And a Sneak Peak of the SR20
- POWDER
- Club Rep
- Posts: 1204
- Joined: Fri May 15, 2009 12:19 pm
- Car: S13
- Engine: SR
- Real Name: Mike
- Location: Johannesburg
Re: Project: Drillergy's Sidewinder
Tjo, u can't be serious, where u pick up that SR from? Has it actually got forgies in? This gonna be fun !!!
Carpe Diemotor - Sieze the motor today
- Nissan 200SX S13 92' SR20DET
http://200sx.za.net/phpBB3/garage_vehic ... cle&VID=14
- Nissan 200SX S13 92' SR20DET
http://200sx.za.net/phpBB3/garage_vehic ... cle&VID=14
- Drillergy
- SX Forumholic
- Posts: 2078
- Joined: Fri Sep 21, 2007 10:18 am
- Car: S13
- Engine: SR
- Real Name: Darryl
- Location: Midrand
- Contact:
Re: Project: Drillergy's Sidewinder
Rods are stock.
On the next rebuild it will get swopped out for Eagles. Then it should be fully forged bottom end.
On the next rebuild it will get swopped out for Eagles. Then it should be fully forged bottom end.
- POWDER
- Club Rep
- Posts: 1204
- Joined: Fri May 15, 2009 12:19 pm
- Car: S13
- Engine: SR
- Real Name: Mike
- Location: Johannesburg
Re: Project: Drillergy's Sidewinder
T the same time do Brian Crower titanium valve springs and valve retainers with a Rocker Arm Stopper and rev her to 9000.... I'll be doing the conversion soon myself....
Carpe Diemotor - Sieze the motor today
- Nissan 200SX S13 92' SR20DET
http://200sx.za.net/phpBB3/garage_vehic ... cle&VID=14
- Nissan 200SX S13 92' SR20DET
http://200sx.za.net/phpBB3/garage_vehic ... cle&VID=14
Re: Project: Drillergy's Sidewinder
Mmmm, turbo looks rather familiar.....it was completely overhauled with new bearing housing, shaft and kit.
The exhaust is .48 AR t3 footprint.Compressor is good for the SR for daily street. The Nissan comp and wheel is to small.
Nice build.
The exhaust is .48 AR t3 footprint.Compressor is good for the SR for daily street. The Nissan comp and wheel is to small.
Nice build.
- poizen
- 200SX Maniac
- Posts: 2994
- Joined: Sat Apr 12, 2008 2:05 pm
- Car: S13
- Engine: SR
- Real Name: Mical Mackay
- Location: Durban, New Germany
Re: Project: Drillergy's Sidewinder
yep sad to sell it but hada blow out on my audi tyre and needed a fix fast and darryl needed a turboBigKriss wrote:Mmmm, turbo looks rather familiar.....it was completely overhauled with new bearing housing, shaft and kit.
The exhaust is .48 AR t3 footprint.Compressor is good for the SR for daily street. The Nissan comp and wheel is to small.
Nice build.
but yes this is going to look great keep us all updated
''enough rice to feed whole of china''
Re: Project: Drillergy's Sidewinder
Sounds good...enjoy !!