Project ANARCHY

Draco · Post by **Draco** » Tue Jul 22, 2014 7:15 am

I've got only 1 box, so that gives u an indication what u want or don't want.

SonOfAnarchy ZA · Post by **SonOfAnarchy ZA** » Tue Jul 22, 2014 7:49 am

Ag its not my daily so loud us good

SonOfAnarchy ZA · Post by **SonOfAnarchy ZA** » Mon Aug 11, 2014 11:06 am

got down to abit more cleaning

before

After

then i pulled the exhaust mani off

only to find out why i wasn't achieving full boost

there were a few cracks

Draco · Post by **Draco** » Mon Aug 11, 2014 1:05 pm

Glad you found the leak Jason, hope you get it running soon!

Riekert · Post by **Riekert** » Tue Aug 12, 2014 12:28 am

Eish bad luck dude

SonOfAnarchy ZA · Post by **SonOfAnarchy ZA** » Mon Aug 18, 2014 11:24 am

Dash came out with some struggling. need to redo the wiring mess the previous owner kindly left for me

Jokat · Post by **Jokat** » Mon Aug 18, 2014 4:07 pm

That looks like a hell of a lot of work! Enjoy!!

R31skylineguy · Post by **R31skylineguy** » Mon Sep 15, 2014 8:59 pm

I feel your pain taking the dash out. Never again am I doing that job again lol

POWDER · Post by **POWDER** » Tue Sep 16, 2014 6:57 am

Lol, have fun dude.... The epic part is when you constantly find another thing out of place as you think your done each time.... Just wish I could find the time to get mine finished, but I keep finding more issues lol

Skippy · Post by **Skippy** » Tue Sep 16, 2014 10:06 am

Intake looking nice and clean.

By the looks of it, I don't think I want to take the dash out lol

troopiec · Post by **troopiec** » Tue Sep 16, 2014 9:09 pm

Good work man! tell me was your manifold made out of steam pipe? hectic crack there wow, surprised it cracked on the actual pipe and not on the welding seam.

SonOfAnarchy ZA · Post by **SonOfAnarchy ZA** » Tue Sep 16, 2014 9:29 pm

Ja it is steam pioe but had no support so welded one in

fuzz123 · Post by **fuzz123** » Thu Sep 18, 2014 4:33 pm

troopiec wrote:Good work man! tell me was your manifold made out of steam pipe? hectic crack there wow, surprised it cracked on the actual pipe and not on the welding seam.

It cracked right on the heat affected zone, which shows that to weld this steam pipe successfully you will have to post weld heat treat the manni and/or control the pre heat and cooling down temperatures much better.

How are you going to fix it J?

SonOfAnarchy ZA · Post by **SonOfAnarchy ZA** » Thu Sep 18, 2014 4:35 pm

Weld the kak out of it[emoji4] will se how long that lasts

troopiec · Post by **troopiec** » Thu Sep 18, 2014 5:18 pm

How long has that manifold been in operaton? My steam pipe one is holding up but has little milage on it since building so it's a bit soon to say, plus I've got a T28 bolted on which is a bit lighter than your t3/4. But time will tell

*Nissan 200SX Club - South Africa

Project ANARCHY

Re: Project ANARCHY

Re: Project ANARCHY

Re: Project ANARCHY

Re: Project ANARCHY

Re: Project ANARCHY

Re: Project ANARCHY

Re: Project ANARCHY

Re: Project ANARCHY

Re: Project ANARCHY

Re: Project ANARCHY

Re: Project ANARCHY

Re: Project ANARCHY

Re: Project ANARCHY

Re: Project ANARCHY

Re: Project ANARCHY